Posts by jay (archived)
311 total posts293 results
cd50 MAB8050H microcontroller chip
in Wanted · Jan 11, 2012 08:55Hi Nick, Fantastic thankyou, i didnt think for a second id get a responce on this one as its a masked chip that i could only get out of an original cd50 just let me know what you want for it
Beogram CD 5500 drawer sometimes closes after opening
in General Discussion & Questions · Jan 6, 2012 08:07change the belt, also the micro switch may need cleaning with a p1200 grit and contact cleaner (carefully) as they tarnish, plus when the door is half way open make sure the same micro switch is centered, they can get be…
MMC1-5 cartridge (in fair or poor condition)
in Wanted · Jan 5, 2012 15:12try an sd card plastic case, once closed it will hold the stylus in place without causing any damage, plus you can see at a glance which mmc is inside regards jay
cd50 MAB8050H microcontroller chip
in Wanted · Jan 5, 2012 10:46could be a long shot but does anyone have an original MAB8050H microcontroller chip out of a cd50 thanks jason
Beolab 3500 POWERLINK version on Iconic AV...any info?
in General Discussion & Questions · Dec 29, 2011 13:16Bear in mind I am not the electronics engineer of our company, Keith is quite right that the BeoLab 3500 works exactly as he described above. Martyn our engineer has re-designed a circuit board to enable any BeoLab 3500 …
Beosound 9000 clamper height adjustment
in General Discussion & Questions · Dec 28, 2011 14:23[quote user="valve1"] [quote user="Dave0280"]do you know of anyone in Brum?[/quote] I know a helpfull guy who might live near you, Jason in Iconic-av......... :-) ! [/quote] Out of respect for the offical engineers aroun…
Beosound 9000 clamper height adjustment
in General Discussion & Questions · Dec 28, 2011 13:20have you tryed slightly adjusting the 2 settings at the back until it stops rubbing and plays well?
xmas
in General Discussion & Questions · Dec 23, 2011 12:09Merry Christmas one and all, wishing you all our best
Beosound 9000 clamper height adjustment
in General Discussion & Questions · Dec 23, 2011 12:06Hi Dave, where did you get the laser changed?
Beosound 9000 clamper height adjustment
in General Discussion & Questions · Dec 23, 2011 09:54Have you checked the 2 adjustments at the back are set to the right position?
beogram beomaster datalink list ?
in General Discussion & Questions · Dec 20, 2011 16:23now i have the datalink list i shall make it easier, does anyone have a list of beomasters that have built in pre amps? even as optional thanks again
Beosound 9000
in General Discussion & Questions · Dec 20, 2011 16:11would have been a cool remote control 🙂
beogram beomaster datalink list ?
in General Discussion & Questions · Dec 20, 2011 15:31thanks but its not the list im after, i have the list of turntable riaas, its a datalink list i need
Beosound 9000
in General Discussion & Questions · Dec 20, 2011 15:25take out the panel, when you put it back in make sure it clicks in properly, if that doesnt do the trick you the red connector may be loose inside the unit but ive never known that happen on its own,
beogram beomaster datalink list ?
in General Discussion & Questions · Dec 20, 2011 14:17Hi all, Does anyone have a complete list of Beomasters / Beosounds and Beograms that support Datalink ? I can trawl through countless service manuals but thought id check first incase someone here had already put in the …
BeoPassion vs BeoObsession
in General Discussion & Questions · Aug 7, 2011 13:20one in the same for me BeoPassession 😎
RL60 metal plate
in General Discussion & Questions · Jul 26, 2011 02:36Nice job Leslie, looks great 🤒
These look great! (good advert too!)
in eBay - the right way! · Jul 19, 2011 13:32B&O did make a wall bracket for these, ive only ever had 2 sets , but the bracket fits in all 3 holes and when tightened the offset screws lock it in tight, completely over engineered , which i loved about them, i dont h…
Ouverture Laser Replacement
in General Discussion & Questions · Jun 6, 2011 07:04It was more directed at members who thought a generic part number would get the right part, then find out the hard way it was wrong.