Beogram 8002 not turning on

in BeoGram · Nov 12, 2025 22:59 GMT

Hello, thanks for the feedback Mark. I re-wired the cable to make sure the grounding pin was connected to the sleeve on the Din plug and that fixed the issue. The 8002 is now sounding great! I'll start work on the busted…

Beogram 8002 not turning on

in BeoGram · Nov 11, 2025 19:20 GMT

Here's the new video

Beogram 8002 not turning on

in BeoGram · Nov 11, 2025 19:19 GMT

Sorry for the poor audio from the previous video. I'm uploading a new one. And yes, the ground wire is connected too.

Beogram 8002 not turning on

in BeoGram · Nov 10, 2025 23:34 GMT

Here's the video with the noise.

Beogram 8002 not turning on

in BeoGram · Nov 10, 2025 23:31 GMT

Hello, how are you? I'm back 🙂 I have new updates. I got a grounded Din to RCA cable in order to connect the 8002 to the amp hoping grounding was the cause of the hissing noise. Sadly, that's not the case. Even with the…

Beogram 8002 not turning on

in BeoGram · Oct 6, 2025 18:32 GMT

Thanks YannChris for the link to the belt, I'll be sure to purchase it. In the meantime I used a regular stationary rubber band and it works pretty well . Of course durability is an issue, but for testing the device it w…

Beogram 8002 not turning on

in BeoGram · Oct 4, 2025 04:00 GMT

Hello, how are you? Just wanted to share great news. I managed to bring it back to life! 🙂 The issue was oxidized base for the IC1 and a bad TR17. I replaced it and cleaned each slot for the IC1 with Deoxit. I now have …

Beogram 8002 not turning on

in BeoGram · Sept 24, 2025 01:40 GMT

Hello, I'm back with an update. I have replaced the fuse and I now get 5VDC at pin P6-1 and on the 01C1 5V regulator. But still no red dot 🙁. So far I've replaced the fuses, replaced the capacitors, checked their correc…

Beogram 8002 not turning on

in BeoGram · Sept 12, 2025 01:24 GMT

Hello, checked all the fuses and the one inside the power brick has no continuity. Going to replace it and will run the tests again. I'll keep you posted. Thanks 🙂

Beogram 8002 not turning on

in BeoGram · Sept 10, 2025 02:53 GMT

Hello, just sharing an update. I've reconnected the severed Din plug. However, I still get bored dot when plugging, no 5VDC at pin 6-1, nor voltage at the 5V regulator. I've checked all new capacitors to be installed cor…

Beogram 8002 not turning on

in BeoGram · Sept 4, 2025 15:20 GMT

Thank you very much! I'll reconnect everything and run the test again. 🙂

Beogram 8002 not turning on

in BeoGram · Sept 3, 2025 23:41 GMT

Thanks, just checked for 5VDC at pin P6-1 with the black lead on negative C27 and got no signs of life. I also want to share that the din plug is completely disconnected, the guy I bought it from told me he wanted to rep…

Beogram 8002 not turning on

in BeoGram · Sept 2, 2025 23:35 GMT

How should I proceed in order to test 5VDC at pin P6-1. I have identified the location of that pin, but where should I contact with the other probe in order to test the voltage? Sorry for the dumb question 😬 Thank you v…

Beogram 8002 not turning on

in BeoGram · Sept 2, 2025 02:56 GMT

Hello, how are you? I have replaced all the capacitors following the cap replacement kit from dksoundparts. Is there an additional step I should follow before plugin it in? What should I expect to see after plugin it in,…

Beogram 8002 not turning on

in BeoGram · Sept 1, 2025 19:44 GMT

Great! Thanks for the response. I'll add the jumper then. Thanks 🙂

Beogram 8002 not turning on

in BeoGram · Aug 30, 2025 00:30 GMT

Hello, how are you? I've been replacing all the capacitors on the PCB. But I have one question. In the instructions that came with the capacitors for the Beogram 8002 from Beoparts shop, it says that on C27 an additional…

BeoSound 1 CD player drivers

in BeoSound · Mar 10, 2025 15:30 GMT

Hello everyone, I recently got the drivers from a BeoSound 1 CD player. Does anyone know the specs for these drivers? The numbers on the back have led me nowhere. Thank you very much

Beogram 8002 not turning on

in BeoGram · Jan 6, 2025 22:38 GMT

Hi Francois, I haven't made any progress on my Beogram. I got the parts Christian recommended, but I haven't got to the soldering yet. I'll venture into re-soldering the capacitors and in case that ends up not being the …

Beogram 8002 not turning on

in BeoGram · Sept 18, 2024 20:54 GMT

Hello, I recently got a Beogram 8002. The issue it has is that it doesn't turn on, not even the red standby dot. I checked the insides and everything seems to be fine. Inside the power supply the fuse and the transformer…