Posts by Struer
131 total posts106 results
Beomaster 3400
in BeoMaster · Oct 23, 2023 03:14Hi Beoworld. I am restoring a Beomaster that has been in storage for a while I realised the output section wasn’t connected to the heat sinks with the two brackets. having fixed this I am now getting a steady 10mv from t…
Beomaster 4400
in General Discussion & Questions · Dec 29, 2021 13:15Hi, I have acquired two Beomaster 4400. One of the units which worked fully apart from the tuner which played finely and didn’t lock into any chanel. The fault is definitely in the tuner board as when I swapped it the tu…
Beomaster 4400 left channel very faint
in General Discussion & Questions · Nov 16, 2021 09:39I have a Beomaster 4400, Left channel very faint on stereo. With hum. Tuner faint. Tape1, tape 2, phono work on mono. Board is clean no marks or work on output section. There seems to have been access under front panel a…
Beogram 4002 (type 5513)
in General Discussion & Questions · Nov 13, 2021 21:35The tonearm is Lifting as it should now. C36 was the culprit.
Beogram 4002 (type 5513)
in General Discussion & Questions · Nov 13, 2021 19:00Yes, the fully working unit I have clicks instantly
Beogram 4002 (type 5513)
in General Discussion & Questions · Nov 13, 2021 17:33Hi, after much work and tests I have managed to get board working almost entirely as it should. All buttons now work as they should and the tonearm drops where it should. The only issue (which I have experienced before I…
Beogram 4002
in General Discussion & Questions · Nov 8, 2021 13:46Hi, I am trying to repair the main board in the Beogram 40002. I know the rest of the unit functions properly. lights function on tonearm and below tonearm. Slow <> both work Issues are as follows: >> only works when I k…
Adjusting the no signal current on a Beomaster 1100
in General Discussion & Questions · Sept 24, 2021 21:25Thanks for this. Still a bit confused though
Adjusting the no signal current on a Beomaster 1100
in General Discussion & Questions · Sept 24, 2021 12:03Hi all, I’m trying to adjust the no signal current on a Beomaster 1100 I have downloaded the manual for BM1100 and BC1800. I would have thought to adjust the trimmers (R155/ R255)to give a output of 10mv across resistors…
Beogram 4002 (type 5513)
in General Discussion & Questions · Mar 4, 2021 10:38Thanks, Working through issues
Beogram 4002 (type 5513)
in General Discussion & Questions · Mar 3, 2021 15:36Thanks for this. In your experience might these faults be related to the need for a recap, as each fault is specific to a different clusters on the main circuit board and but pointed to any one transistor. I may be missi…
Beogram 4002 (type 5513)
in General Discussion & Questions · Feb 26, 2021 11:50Hi, I recently acquired a spare Beogram 4002 (type 5513) US Model with a 110v fixed voltage.The main board (8005016) is in cosmetically nice condition with little or no previous tampering. However not all functions work.…
Beomaster 6000 Type 2702
in General Discussion & Questions · Feb 9, 2021 12:52Hi all, I have a Beomaster 6000 Type 2702 that plays on 3 outputs, but the rear right plays through the speaker only for a few seconds before the sound fades out completely. (It is not an issue with the speaker or speake…
Beomaster 6000 quadrophonic tape/ aux
in General Discussion & Questions · Jan 2, 2021 22:53Thanks, appreciated
Beomaster 6000 quadrophonic tape/ aux
in General Discussion & Questions · Jan 2, 2021 19:41Ok, thanks for this. I have played a beocord 5000 through the tape 4 in the past with all 4 speakers playing sound, but not quadrophonic sound obviously. Do you have a phono to din converter for your various sources. I’m…
Beomaster 6000 quadrophonic tape/ aux
in General Discussion & Questions · Jan 2, 2021 14:49Hi all, has anyone been able to get 4 distinct cassette audio channels through the auxiliary connection in the Beomaster 6000 quad. I’m aware that the Beomaster 6000 was designed to decode quadrophonic cassette tapes but…
Beomaster 6000/ beogram 4002/ beocord 5000
in General Discussion & Questions · Dec 15, 2020 16:53Ha, thought you might have inside information
Beomaster 6000/ beogram 4002/ beocord 5000
in General Discussion & Questions · Dec 15, 2020 14:11Hi, does anyone know for sure what process was involved in the finishing of the control panels of Beomaster 6000 quad/ beogram 4002/ beocord 5000? Was it an anodised process on etched aluminium or a brushed / linished la…
Beogram 4002 5514
in BeoGram · Dec 2, 2020 09:32The 4002 now drops as it should the tracking arm seems to operate, unfortunately the motor now does not operate on 33 rpm. The saga continues