Posts by AudioOrigin
51 total posts50 results
Beogram 6500 Skipping
in General Discussion & Questions · Sept 26, 2019 18:57Hello, To me it sounds very likely that the suspension in cartridge is failing, Especially due to this comment “I get a little improvement at the maximum tracking force” If you want to post me the cartridge I can test it…
Beogram 3000 5228 freewheel pull problem :(
in General Discussion & Questions · Sept 26, 2019 18:43Hello, A small piece of leather works very well you can use a hole punch to get it the right size for a tight fit put shinny side up, if you don’t have any leather scrap, I can send you a leather disc to put in the hole.…
Beogram 1202 distorted sound
in BeoGram · Sept 26, 2019 17:08Hello, I rebuild all B&O styli and cartridges including the B&O sp14, feel free to contact me regarding rebuilding your SP14 I can also examine it for stylus wear under a microscope before any work is carried out to conf…
Repair Beogram 1202 lid
in BeoGram · Sept 26, 2019 17:00Hello George May, The original Beogram 1202 lid has no hinge you probably have a beogram 3000 lid on it, or a 2000 if it’s black, both of which do fit the Beogram 1202 perfectly. The easiest solution would be replacing t…
wanted beovox m75 tweeter
in Imported Content (Unmapped) · Jun 9, 2019 18:16Hi, I am looking for a Beovox m75 tweeter as one of my ones are open circuit. If anyone is willing to part with one please message me thanks. Best regards Alistair
Lift button assembly on my Beogram 2000
in Imported Content (Unmapped) · Jun 8, 2019 16:44Hi Carl , The main job on that beogram to make it work properly is a motor rebuild, and it also likely needs a new stylus if your stylus has been used for about 1000 hours it should be replaced or professionally rebuilt …
Lift button assembly on my Beogram 2000
in Imported Content (Unmapped) · Jun 7, 2019 17:45Hi , The ball bearing makes the rotating selector sit in the right positions, so it’s not loose. I will upload images but I think you will need to replace the plastic part. Best regards Alistair Audio Origin
Lift button assembly on my Beogram 2000
in Imported Content (Unmapped) · Jun 6, 2019 16:28Hi Paul, I am in Southampton also; I should be able to supply any parts you need. If you upgrade your beoworld membership to silver you can Download the manual to help you fix it and also you can ask other Beoworld membe…
Beogram 3400 intermittent tonearm movement
in Imported Content (Unmapped) · May 25, 2019 19:58Hi, When it does not work properly does the platter still rotate? Best regards Alistair
beogram rx - tone arm keeps sliding back to end position
in Imported Content (Unmapped) · Mar 10, 2019 12:02Hi, The counterweight is common fault on this design of tonearm, it can be remedied with some supper glue, I would advise using a high viscosity super glue. From your description my guess would be the diamond has detache…
ADVICE: Beocenter 1800 specifically the MMC3000 Stylus
in Imported Content (Unmapped) · Mar 8, 2019 23:32Hi, Those images have very little detail, what I can tell you is that the diamond is present and I cannot see any issues, this does not mean its ok, Stylus wear cannot be viewed at this magnification, also suspension fai…
Beogram 1600 speed problem
in General Discussion & Questions · Feb 27, 2019 01:29Hi, " I checked the service manual from the Beogram 1102, so i think the adjustment should be like this? (seen in the image attached) Fine adjustments " No that is to adjust the cueing point for the 7 inch and 12-inch re…
Beogram 1600 speed problem
in General Discussion & Questions · Feb 26, 2019 00:17Hi, “ “Sadly“ i have the version without the pitcher above the rocker switch. Thats why i thought that maybe there is something like a fine adjustment inside the turntable. ” I have never seen this model but I should ima…
Beogram 1600 speed problem
in General Discussion & Questions · Feb 22, 2019 22:49Hi, Yes, there is an adjuster inside all the info is in the service manual Best regards Alistair
Beogram 1000 motor types and pick-up
in BeoGram · Feb 22, 2019 22:23Hi, The important thing is you have right stylus for the cartridge I have often seen one of the following (sp14,sp10,sp12) on the older metal cartridge this is wrong the collar stops the stylus from going on properly as …
MMC 6000 right channel issue
in General Discussion & Questions · Feb 19, 2019 02:46Hi, “if balance to right and power up the amplifier (a lot) I can hear but in normal condition just got the left channel sound. ” Are you actually getting both channels? i.e. using a test record? Best regards Alistair Au…
Got a Beogram 4000 and RX2 turntable...need advice
in General Discussion & Questions · Feb 8, 2019 22:51I recently sold a bg4000 platter to Craig here on the forum, he might sell you his poor condition one if you don’t mind it looks a bit corroded. If you want a better condition one, I might be willing to part with another…
A Beogram 4000
in Imported Content (Unmapped) · Feb 7, 2019 01:15Hi Craig, I’m glad you could hear the difference, the spec is Nude Micro Ridge diamond boron cantilever And the end bit is a 3d printed replacement Best regards Alistair