Posts by hunchbacker
38 total posts32 results
MMC 6000 Setting Question
in BeoGram · Oct 17, 2025 13:38thanks pretty much confirms what I have found.
MMC 6000 Setting Question
in BeoGram · Oct 15, 2025 23:59Currently have my 4002 up and running again after a much needed damper lubrication and pivot arm cleaning. My receiver has both MM and MC settings. I've noticed the output is lower than my other turntables when on the MM…
Beogram 4002 Restoration
in BeoGram · May 22, 2024 04:26Exceptional work Christian. I came here for the restoration and stayed for the plinths. I've had my 4002 for about 2 years. It came without a plinth so I made a quick replacement. Have been looking for something more tru…
Beogram rx question SOLVED
in BeoGram · May 21, 2024 17:26UPDATE: Solved After toying with tracking to no end with no improvement I decided to take a hard look at the platter. I discovered it was high on the tone arm side. Low on the left. Pulled the platter. Adjusted the heigh…
Beogram rx question SOLVED
in BeoGram · Mar 30, 2024 12:16I was lucky enough to pickup this gem today at the GW. (Not to be confused with the rx2) I tested it before buying and all mechanics worked. It had an mmc4 cart but without any way to test it I took a chance. So I got it…
Beogram rx question SOLVED
in BeoGram · Mar 30, 2024 10:31Good thoughts. Will check all those options when I have time today or tomorrow. Thanks
Beogram rx question SOLVED
in BeoGram · Mar 30, 2024 02:02When I clean it I don't hear anything. My other turntables do make a noise when I brush them. Maybe a manual will offer a clue. I think I read the 1700 manual is very similar. Have not looked deeply yet for the rx manual…
4002 Tone Arm Next Step?
in BeoGram · Feb 28, 2024 04:00Yes I can test the circuit. I don't believe they did anything else(if even that) The linkage was so clean I am wondering if they just cleaned it up and did not even replace the solinoid. Not real fond of that shop right …
4002 Tone Arm Next Step?
in BeoGram · Feb 27, 2024 03:55Second owner on this table. Had it serviced and was told solenoid was bad. Had it replaced. Worked wonderfully for 6 months. Then tone arm decided not to drop...again. Everything else works as it should. Pulled damper an…
Beogram for BeoMaster
in BeoGram · Apr 9, 2023 21:09I realize this post is several months old but I thought I would toss in my 2 cents. There is a very good repair shop in Gig Harbor, WA. They deal in high end components and know their stuff. They just serviced my Beogram…
To retip or not to retip MMC6000
in Cartridge · Apr 5, 2023 04:00Ended up finding a retipped mmc6000 on the bay. Rebuilt by Joseph Long (Groovetickler), using the original beryllium cantilever, and retipping with a .12mm square nude .2 x .7 mil elliptical diamond. Thanks to Beoworld m…
To retip or not to retip MMC6000
in Cartridge · Apr 2, 2023 14:57Thank you. I see his wait time is 1-3 months. Maybe that is normal but being in Wa State, USA I am not sure I have the patience. :) I am also looking into replacing it. Since posting I have contacted Soundsmith here in t…
To retip or not to retip MMC6000
in Cartridge · Apr 2, 2023 05:06I recently picked up a steal of a deal on a original owner 4002 TT. ( see "Should I spend $75" in this forum) It only needed a belt and solenoid to get the arm to properly scan and drop. I was blessed with a mmc 6000 in …
Should I Spend 75$?
in General Discussion & Questions · Feb 27, 2023 16:56Will know more in a week when belts arrive.
Should I Spend 75$?
in General Discussion & Questions · Feb 27, 2023 14:36The paper work that came with it says that it does. Still learning. Any advantage today other than quality?
Can You Identify These? 4002
in BeoGram · Feb 27, 2023 03:54This MMC6000 cartridge case was included in a recent 4002 purchase. Inside were these parts. Can anyone tell me what is there and the one tool missing?
Should I Spend 75$?
in General Discussion & Questions · Feb 26, 2023 21:51With out a doubt a keeper! May have to move one of my other 3 tts though. :)