Posts by styppen
112 total posts97 results
How to connect a 5500 or 6500 system to speakers and a tv
in BeoSystem · Jan 11, 2024 19:24I connected my TV to my Beomaster 5500 by connecting the TV/AUX port on the Beomaster to the TV headphones output. Additionally, I've disabled TV speakers. I got the needed cables from Steve :)
The RX2 TT : tell me about yours plz
in BeoGram · Jan 4, 2023 15:32I have a Beogram 5500 which is not exactly the same as RX2 but it was made roughly around the same era. As far as cartridges go, you are correct. They are expensive but they can be found. Other than that, my TT has been …
Beolab 8000 Dilemma
in BeoLab · Sept 18, 2022 08:47You sort of summarized my thoughts. I've been thinking the same thing as you've pointed out. The 8000s were a bargain and spending for Beolab 19s feels not right. I've found a decently priced Beolab 11 and I'll give it a…
Beolab 8000 Dilemma
in BeoLab · Sept 17, 2022 13:45Die_Bogener wrote: For music you dont need more than 2 good speakers. Any speaker more makes it worse. Music and something like Dolby 5.1 is not working. It sounds great some hours and then you notice: there is something…
Beolab 8000 Dilemma
in BeoLab · Sept 16, 2022 11:00I've read that Beolab 2 is a great subwoofer for movies but not music. I'm sort of inclining towards the Beolab 11 now. Less powerful than 2 and 19 but should be enough to compensate the lack of bass on 8000s.
Beolab 8000 Dilemma
in BeoLab · Sept 16, 2022 08:53Die_Bogener, thanks for pointing this out. You are correct, Beolab 19 only has one powerlink input. I must have confused it with Beolab 11 subwoofer. Thank you for also pointing out the issue with mixing analog and DSP s…
Beolab 8000 Dilemma
in BeoLab · Sept 16, 2022 07:07Interesting, I haven't heard about this delay. But I assume if 8000s are connected to the 19 itself the delay should be gone, right?
Beolab 8000 Dilemma
in BeoLab · Sept 15, 2022 08:59Hi Beoworld I’m in the process of updating and upgrading my home setup. I’ll take the liberty to tell the whole story so bare with me. Until now, my setup consisted of the following components: Beomaster 5500 Beovox S45-…
Powerlink - Power Up vs Speaker On
in General Discussion & Questions · Sept 12, 2022 07:25Hi trackbeo, thanks for your reply. I did some reading on the archivedforum2 and found some useful information. I'm trying to connect my non-B&O streamer to Almando Powerlink switch and the input expects a trigger signal…
Powerlink - Power Up vs Speaker On
in General Discussion & Questions · Sept 10, 2022 07:50I've been looking at the Powerlink wiring connections on BeoTech page and I have a question. Given the diagram below, what is the difference between 1 - Power up and 4 - Speaker on signals?
Beolab 8000 rubber feet
in BeoLab · Sept 8, 2022 14:28Thanks Tignum. Exactly what I'm looking for!
Beolab 8000 rubber feet
in BeoLab · Sept 7, 2022 08:16I'm looking for metal bolts with rubber feet. The same as Tignum posted in his first photo. I would really like to get the original replacement parts. If I'm not able to find any, I'll conjure something up with generic b…
Beolab 8000 rubber feet
in BeoLab · Sept 6, 2022 08:55Hi all Any ideas where I could get rubber feet for the base for Beolab 8000? My 8000s came without rubber feet I would really like to add them since the speakers are standing on a hardwood floor. Thanks!
Bang olufsen beomaster.
in BeoMaster · Aug 29, 2022 07:40I haven't used that specific combination but I imagine there shouldn't be any problems. The pre-outs on Beomaster 6500 and 7000 output normal line-level signal.
DIY Beolab 8000 Wood frets (STLs included).
in BeoLab · Aug 25, 2022 13:46I have a question regarding the dimensions in the STL file. When I opened the files the size looks a bit off. @matador, can you confirm if multiplying the scale factor for x100 will get the right dimensions?
Lee's S45 speaker
in Imported Content (Unmapped) · Dec 20, 2021 06:37I have a pair extra. Let me know if you're interested.
Beolab 3 to non B&o amp
in General Discussion & Questions · Nov 9, 2021 20:16Hi Jack! I have a similar setup. I have Beolab 3 speakers connected to RCA line level pre-outs on my Beomaster 5500. Each RCA output goes to one Beolab speaker. You will need a specific cables to achieve this (powerlink …
beogram 1202 platter on beogram 3000
in General Discussion & Questions · Oct 6, 2021 19:22BG1202 platter should be fine on BG3000. The hole cutouts are the same so should br fine. As far as the motor goes … I think they should be the same.
Beomaster 5500 with non B&O turntable
in General Discussion & Questions · Apr 3, 2021 21:34BM5500 has a built in RIAA amplifier. Should be fine by connecting the turntable either to PHONO-DIN or RCA inputs.
Pulling my hair out
in General Discussion & Questions · Jan 19, 2021 08:42When you press PLAY button on Beogram 5500, the selected input on Beomaster should change to PHONO.