Posts by chilibt
41 total posts38 results
After Recap Kit done, still a CD problem Beocenter 9000
in BeoCenter · Mar 18, 2023 20:21Hi Attached is the before and after pictures of the recap. The symptoms before the recap remained after the recap: the first CD played, then it never did again. The fact the first CD played tells me the recap is probably…
After Recap Kit done, still a CD problem Beocenter 9000
in BeoCenter · Mar 17, 2023 18:49The first 2 videos were compressed and may not be viewable so here is the uncompressed version where the laser hits the end. This is maybe 1 of 8 times. Another 1 in 8 times it goes half the distance and just shows outsi…
After Recap Kit done, still a CD problem Beocenter 9000
in BeoCenter · Mar 17, 2023 18:41here is another video of just the lens
After Recap Kit done, still a CD problem Beocenter 9000
in BeoCenter · Mar 17, 2023 18:27Hi, I carried out further diagnosis before I do any electrical adjustments (i have seen some warnings on other posts and am cautious). When selecting CD, 3 out of 4 times the disc spins then shuts down. 1 in 4 times the …
After Recap Kit done, still a CD problem Beocenter 9000
in BeoCenter · Mar 16, 2023 11:43Hi My latest project is a a bit frustrating. I got this Beocenter 9000 which worked except the CD would not read the disk after the first attempt (the first attempt worked only). Subsequent attempts with 6 different CD d…
First start of a BM6000 "not Working"
in BeoMaster · Mar 11, 2023 21:45Thank-you for all the help!!! It was an installation of 100 and 100k trimmers that caused both problems, the LED for the FM strength AND the no load current setting issue. I did verify the correct trimmers were installed…
First start of a BM6000 "not Working"
in BeoMaster · Mar 11, 2023 20:45I think I found the problem... standby.
First start of a BM6000 "not Working"
in BeoMaster · Mar 11, 2023 20:27Hi, Yes the amp was in operation prior to the recap. I did no adjustments until after the recap so the perhaps the problem may have existed prior to the recap, or it is after, I am unsure. But it was in use. Now when I a…
First start of a BM6000 "not Working"
in BeoMaster · Mar 11, 2023 14:22Any thoughts on what next to look at for this problem?
Beocord 8000, 9000 Take-up reel rebuild
in BeoCord · Mar 11, 2023 04:49Thank you for the advice. The cap did come off with careful prying using my fingernails, one nail on both sides. Some twisting and tilting got it off with a bit of force. It was cleaned and reassembled. The cap clicked b…
First start of a BM6000 "not Working"
in BeoMaster · Mar 10, 2023 19:01It looks like the Tr 201-205 read ok unless I am not reading the tester properly (attached Photos)
Beocord 8000, 9000 Take-up reel rebuild
in BeoCord · Mar 10, 2023 17:51I understand, my thoughts exactly. As there is a part number for each side, and a separate for the tip so they must come off? Perhaps removal destroys the old tip and once on, the new tip cannot be easily removed? Do you…
Beocord 8000, 9000 Take-up reel rebuild
in BeoCord · Mar 10, 2023 15:15Hi, thanks for the questions. No matter how I try, I always leave out something important. yes the brake pad was set inside, and the stiffness in the Black plastic reel was not discovered until removed as in the photo. I…
Beocord 8000, 9000 Take-up reel rebuild
in BeoCord · Mar 10, 2023 01:59I recently replaced the rubber 'tires' for the idler wheels in the tape drive mechanism for my not working BC 9000 and installed new belts. Once tested it did not turn. Upon comparing the Take-up reels from my older Beoc…
First start of a BM6000 "not Working"
in BeoMaster · Mar 3, 2023 23:31Thanks for the tips, I checked voltages and so far could not see any differences from left and right channel: r116/216 -47.6 TR102/202 collector +47.2 D107/207 +28V TR111/211 e -47v As for voltages at speaker output it s…
First start of a BM6000 "not Working"
in BeoMaster · Mar 2, 2023 18:45a new item, No load current issues: I thought I would carry out the no load current adjustment. The unit is operating for a few days in radio and tape after full recap. This morning I start: Right channel done, set to 22…
First start of a BM6000 "not Working"
in BeoMaster · Mar 2, 2023 16:02Thanks Glitch! my thoughts were the same about traces, except the intermittent display threw me off. I started to think a cap or TR was changing in temperature causing the problem, with the displays then they may affect …
First start of a BM6000 "not Working"
in BeoMaster · Feb 28, 2023 23:36The arrow in the photo was where 11 traces were cut, the white wires are my jumpers.