Posts by traverso
180 total posts151 results
Beovox 5700 TWeeter impedance
in BeoVox · Nov 26, 2024 17:44Hello; Can you please indicate to me the resistance value of the HF 2000 tweeter of the Beovox 5700. The beovox 5700 is a 8 Ohms speaker as well as the installed Philips boomer and the medium but I have a doubt about the…
Beomaster 1900 IL1 Testing
in BeoMaster · Nov 6, 2023 18:00The LDR components were the culprits I used a repair kit from Beoparts and put back the LDR in the 1900, everything is fine The 1900 is back to life and sing again Thank you Sonavor
Beomaster 1900 IL1 Testing
in BeoMaster · Oct 27, 2023 10:17Actually I unsoldered the LDR, more easy to open it The metal cover is glued to the black plastic support see attached picture The lamp is dead
Beomaster 1900 IL1 Testing
in BeoMaster · Oct 27, 2023 09:08The lamp is probably OK as measured 17 Ohms However I have ordered a repair kit for this LDR By the way, is there a trick to remove the cover of this LDR? Is it glued or just clipped?
Beomaster 1900 IL1 Testing
in BeoMaster · Oct 26, 2023 18:41Hello, Thank you for the help I used a one Khz tone generator connected to the recorder input and the signal arriving at the balance control is very low I will open the LDR by tomorrow for checking Alain
Beomaster 1900 IL1 Testing
in BeoMaster · Oct 26, 2023 10:34I could measure the IL1 lamp resistance between emitter TR24 and 15 V and found 17,7 Ohms is this value OK? If yes the problem is elsewhere, any thought?
Beomaster 1900 IL1 Testing
in BeoMaster · Oct 26, 2023 10:10Hello, The input signal is not reaching the balance potentiometer It is stopped at Test Point 200 or 300 and not going through R226 and R326 I suspect IL 1 to be faulty and would like to know how to test the lamps inside…
Beomaster 3400 Problems
in BeoMaster · Aug 3, 2023 10:21I lately discovered your message Concerning the Service Manual I may send it if you are still interested. Cheers Alain
Beomaster 2400 cannot switch to FM5 !
in BeoMaster · May 31, 2023 15:09The culprit was R126 measured 40 MOhms
Beomaster 2400 cannot switch to FM5 !
in BeoMaster · May 31, 2023 12:07Yes! I used FM4 to activate FM5 and it works as follows: the R122 and R126 lifted from the IC6 side the R122 connected in place of R126 on IC6 side So the issue is between TR21 and the IC6, to confirm I have to replace t…
Beomaster 2400 cannot switch to FM5 !
in BeoMaster · May 30, 2023 19:36The signalling only is on an other PCB not the commands
Beomaster 2400 cannot switch to FM5 !
in BeoMaster · May 30, 2023 14:51Yes it was always there (By the way I measured the lamps they are 18 Ohms each instead of 12/14 Ohms as a consequence, the voltage reference for muting measured at R3, 33Ohms of PCB 5 is no longer 2,5 Volts but 1,9 Volt)
Beomaster 2400 cannot switch to FM5 !
in BeoMaster · May 30, 2023 13:36No it does not if I am on an other entry However, it starts the 2400 when in stand by but does not allow to use FM5 the corresponding lamp is not lit, but in that case I may switch to any other input Alain
Beomaster 2400 cannot switch to FM5 !
in BeoMaster · May 30, 2023 12:54Hello, I am renovating a Beomaster 2400 and identified the following issue. When trying to activate FM 5, it does not happen and the 2400 remains on the actual selection, whatever. Although I may access any other entry t…
Beomaster 4400 faulty issue
in BeoMaster · May 20, 2023 12:29actually it was one leg of the P6 switch to be grounded, stangely it was not. If left open the front end is missing the voltage for the varicaps and it is free running
Beomaster 4400 faulty issue
in BeoMaster · May 19, 2023 16:15Hello After checking some parts ofthe 4400, it appears that one end of the P6 pot for adjusting the channel number 6 is left open when it should be grounded. To be corrected of course. Hopefully can be done without diffi…
Beomaster 4400 faulty issue
in BeoMaster · May 17, 2023 08:54Hello, I have here a new behavior of my 4400 unit I dont know how to correct. When switching from an FM selection to Tape 1 or 2, or Phono, the display related to FM stereo lamp and tuning indicator remains lit for somet…
Beomaster 4400 faulty issue
in BeoMaster · May 5, 2023 09:13Thanks for your feedbacks I will look at it accordingly, since then the situation changed and now when switching on a big bump occurs immediately and the unit is working I rememeber the previous 4400 I repaired there was…
Beomaster 4400 faulty issue
in BeoMaster · May 4, 2023 12:47Hello, I have here a Beomaster 4400 recently acquired, the project is to change the caps soon. However before starting this I like to correct the following issue. When switching on, I can have: either a proper working of…