Posts by omminp
20 total posts17 results
BGAdaptor - Control a Data Link source with Connected Audio
in General Discussion & Questions · Nov 8, 2026 09:34Hi thanks for posting this . I have a slightly different use case, and I wonder if it is possible to use/adapt BGAdaptor to address it. I have a Beogram CD 3300 which is connected to a non-B&O amplifier driving a pair of…
Galet presseur pour Beocord 2000 Deluxe
in Français · Oct 3, 2026 05:37Hi there, maybe worth looking at this https://www.aliexpress.com/item/1005008052059063.html?spm=a2g0o.tm1000063736.appPushSupportRecommend.33.30881f71hxdb6A&gps-id=appPushSupportRecommend&scm=1007.67346.516851.0&scm_id=1…
Beocenter 2200 tonearm lift problem
in BeoCenter · Jun 21, 2025 06:54To tidy up, the problem was a mechanical fracture and the solution can be found here #60614
Beocenter 2200 Tone arm lowering problem
in BeoCenter · Jun 21, 2025 06:43I found this to be helpful as well. https://www.vintage-radio.net/forum/showthread.php?t=176737 In my case, the mechanism lost the plastic ears on both sides. I used the bent wire idea from the attached thread and held i…
Beocord 2000 Delux K - When gear is moved to play it makes mechanisl noice
in BeoCord · Aug 30, 2024 06:03Hi, seems like you have made some progress - good. Your question 1. First thing to check out is your external source, it would be helpful to know what that is and how it is connected to Beocord. An easy source would be a…
Beocord 2000 Delux K - When gear is moved to play it makes mechanisl noice
in BeoCord · Aug 21, 2024 04:40Hi, the brrr noise happens when the joystick is moved from neutral to any of the operate positions when either or both of the 2 tape sensors is activated. One sensor on the right hand side of the tape head block is trigg…
Beocenter 2200 tonearm lift problem
in BeoCenter · Aug 20, 2024 08:51My Beocenter 2200 tonearm will not lift and raise properly. I have soaked the mechanism from the tonearm suspension down to the floating chassis with IPA and dried it off. Then tried to setup as described in the service …
Beogram 1600 cartridge adjustment
in BeoGram · May 15, 2023 08:25From the photo, it looks like it is missing the counterweight. That needs to be in place so the arm can be balanced....
2nd hand Beocord 2000 Deluxe - Critical points to check
in BeoCord · Jul 11, 2022 02:53Hi and thanks for the videos. The noise doubles in frequency and becomes more intrusive as the speed increases. The idler is causing the noise, a bit annoying for you. Maybe worth swapping the idlers in the short term as…
2nd hand Beocord 2000 Deluxe - Critical points to check
in BeoCord · Jul 10, 2022 08:33It all seems very promising for Beocord. There were 2 models, the K which had a wooden case, and the T which was a 'portable' with a plastic case. You mention a plastic bottom bit and a wooden case top. I assume you have…
2nd hand Beocord 2000 Deluxe - Critical points to check
in BeoCord · Jul 9, 2022 04:34Hello Yann, great that the heads are working - you can get on and recover the tapes now. A good clean of the tape transport with IPA may be worth doing before going too far. Re your interconnect issue, it is also possibl…
2nd hand Beocord 2000 Deluxe - Critical points to check
in BeoCord · Jun 30, 2022 05:23I have found that the critical issue with these machines is the heads. It seems the original Bogen heads have a high failure rate, all but the erase head which seems to be a survivor. Often the other heads will be open c…
Beomaster 3000 type 2937 - RIAA problem
in Imported Content (Unmapped) · Jun 30, 2015 06:48For benefit of anyone searching this thread, the problems were resolved as follows: General hum increasing with volume control settings was fixed by replacing the filter cap C2 on the 24V supply line. The first replaceme…
Refurb Beovox CX100's #xxxx
in Imported Content (Unmapped) · May 12, 2015 12:01Really impressed with the restored CX100's. I have a pair I am working on, white, and I wonder what the stripes looked like originally. On my boxes, the stripes on one side are a dark cream colour, on the other side a mu…
Beogram 5500 17cm record detection
in BeoGram · Nov 18, 2014 03:49Thanks Martin. That explains everything I see. Don't often use 7" records, will be more careful with them in future. And the other hints are appreciated too - seems I may be the only person who doesn't know about this!
Beogram 5500 17cm record detection
in BeoGram · Nov 14, 2014 04:56My Beogram 5500 has been fitted with new drive belts, and a newly refurbished cartridge from Axel. Everything worked well until I tried to play a 17cm record. The player didn't recognise the smaller record, and dropped w…
Beomaster 3000 type 2937 - RIAA problem
in Imported Content (Unmapped) · Mar 18, 2014 01:26Hi, I am new to this forum. I have a BM3000 with a history and some unresolved issues. It seems that this unit was for the European market 220V and arrived in Australia where it was used on 240V (I can see where the orig…