marcthut wrote:

ks!Hello

How Do I downgrade to software 1.7.2.

Thanks!

+1. Instructions on how to do a downgrade would very much appreciated!! 

Running my Beovision 6 in analog mode since i installed 1.7.1 (and 1.8.9). The screen blacksout every 10 sec. when using the DVB-HD module. Worked fine before with 1.4.7.

Thanks! 

 

hprimdahl wrote:

marcthut wrote:

ks!Hello

How Do I downgrade to software 1.7.2.

Thanks!

+1. Instructions on how to do a downgrade would very much appreciated!! 

Running my Beovision 6 in analog mode since i installed 1.7.1 (and 1.8.9). The screen blacksout every 10 sec. when using the DVB-HD module. Worked fine before with 1.4.7.

Thanks! 

 

 

Hi!

Downgrade as follows:

1. Switch the television to standby.
2. Insert the USB pen (With the software version you want to install) in the
    USB slot of the DVB-HD module.
3. Press TV on the remote control
4. Wait for 4 minutes - no feedback is given while the software
     is being updated
5. Disconnect the television from the mains. (Do NOT switch it to standby first)
6. Remove the USB pen
7. Reconnect the television to the mains
8. Press DTV on the remote control
9. Check that the software version is correct
If the software update does not start at all:
1. Make sure that the correct update files are available on the USB pen
2. Try again with a different USB pen

Good luck!

Räuber

Raeuber wrote:

Hi!

Downgrade as follows:

1. Switch the television to standby.
2. Insert the USB pen (With the software version you want to install) in the
    USB slot of the DVB-HD module.
3. Press TV on the remote control
4. Wait for 4 minutes - no feedback is given while the software
     is being updated
5. Disconnect the television from the mains. (Do NOT switch it to standby first)
6. Remove the USB pen
7. Reconnect the television to the mains
8. Press DTV on the remote control
9. Check that the software version is correct
If the software update does not start at all:
1. Make sure that the correct update files are available on the USB pen
2. Try again with a different USB pen

Good luck!

Räuber

Hi Räuber - Thank you very much!!! Works perfectly :)

 

Thank you for the Instructions. But where do I find the Version 0.1.7.2.0? Where can I download? Or somebody will email it to me?

Than you!

Marc Thut

Is a Beosystem 3 software update history kept anywhere on this site?  I'm considering updating my BS3 Mark I from SW 5.0.8 to the latest, but don't know what added features and bug fixes I'd get from doing this.

Any advice as to whether updating would be a mistake?

-- Paul

Hi there,

Unfortuntely I've not found a single home for the rev history and hopefully someone with access to the service tool can update this thread. Going through this thread and some others on BV7 MkIII onwards you'll see lot of bug fuxes.

V5.x you have was fairly robust.

V6.x - V8.x were shockingly bad, with every fix being made they introduced an additional bug.  However, this was also the period when they introduced many new features including 24P. V8.x also introduced support for the internal Blu-Ray drive and support for new screen types MKIV.

V9.x had some link room issues, especially with Sky boxes. This also introduced a new style menu system in black to the left-hand side - which is especially good for Sky and Blu-Ray.

V10.x this is the first version that is as in a par for reliability with your V5.x. However, it still features handshake issues with Sky 1TB boxes on first use.

I believe we are on V11.x  today, but have not tried it myself yet. I'm hoping it may have additional HDMI issues fixed, but expect it to be the version that was mostly developed to support 3D. 

Obviously this is a purely personal update on the version history.

My TV is still under warranty and have not had the bravery to pick up the phone yet to get them to come out under warranty - again - to apply this next update hoping that after nearly 5 years of ownership I'll finally have a TV that is 100% reliable. But if the bug list features anything about HDMI, then I'm definately giving them a shout...

Anyone got the V11 update history?

Mark.

 

I run a commercial Panasonic plasma display off the BS3. According to my dealer, the more recent SW updates broke compatibility with 3rd party displays, and that the January update would fix that. I'm guessing that's the version 11 you mentioned.

First post updated with everything that was discussed here... 😁

Feel free to give more details about missing updates/changelogs 

mbee wrote:

First post updated with everything that was discussed here... 😁

Feel free to give more details about missing updates/changelogs 

Great job, however the latest BS3 software (at least on BV 7-40) is 10.05a not 10.02. Dont know much about releasedate or log however, maybe someone else can fill this in.

/Ehlerz

Thanks Ehlerz, but in fact the 10.05 is already in my first post : look at the lines in bold to find the latest software, underneath is the changelog and then the version history I could get.

I added a line with "(no changelog)" to the BS3 in order to make the software visible. Maybe I should change something to the form of this first post as it becomes BIG! ❓