turbotol,

Which every channel is active on the switch should be reflected by a green led light while the others stay red, even when the switch in standby mode.  It sounds as if the previous user programmed the HDS4 to act like one of the 5-alternate built-in code sets thus it is reacting to commands just not the correct ones.  I would suggest resetting the switch in order to get it back into its default factory settings which would be what the BS1 is sending in order to command the switch.

The IR codes should be present in the BS1 and will be sent as long as you have the Zektor switch setup as your Switch under External Sources.  Other then that you will need to run an IR transmitter from the V.Aux output of the BS1 to the front of the Zektor switch so it will receive the commands as they are sent.

As for inputs on the Zektor switch I believe it to be configured as 1-TV 2-SAT 3-V.Aux 4-DVD, but your Devices must be setup under External Source as well before the BS1 will pass IR command for them, thus allowing you to switch the Zektor to DVD or V.Aux, etc...

The Zektor switch will always be in standby mode when powered on, it will briefly wake and switch when a command is sent and then revert back to standby, thus you will always see it with dimmed LED lights one of which will be green, reflecting the currently select input.

Hiller

Hi Hiller,

Thank you for your help.  Unfortunately after following all your instructions, the Zektor switch still does not funtion properly.  It has happened twice that for some random reason it works for a while but then it goes back to its behavior where it switches immediately back to standby mode after switching inputs.  

Zektor has also not responded to my emails.  They told me on the phone they will only reply by email for problems with products purchased on ebay  (the HDS4 is discontinued) but so far I have not heard back from them.

At this point I would like to pursue other options.  Does anybody use a different brand switch that they can recommend?  Thank you.

Turbotol

turbotol wrote:

Hi Hiller,

Thank you for your help.  Unfortunately after following all your instructions, the Zektor switch still does not funtion properly.  It has happened twice that for some random reason it works for a while but then it goes back to its behavior where it switches immediately back to standby mode after switching inputs.  

Zektor has also not responded to my emails.  They told me on the phone they will only reply by email for problems with products purchased on ebay  (the HDS4 is discontinued) but so far I have not heard back from them.

At this point I would like to pursue other options.  Does anybody use a different brand switch that they can recommend?  Thank you.

Turbotol

I'm really surprised by your experience with Zektor. A few years ago, I had probably THE most postive experience with Zektor giving me the best customer service I've ever encountered. Zektor readily offered to replace my box with an updated, brand new box, because they said they wanted me to have the best possible product from them. They even paid for shipping. The man I talked to took the time to completely walk me through the entire setup. Perhaps your difficulty is in trying to communicate via email. Some businesses, myself included, refuse to converse back and forth via email when a phone call can be so much warmer and friendlier. You just can't hear the friendliness of someone's voice via email. Perhaps a kind phone call will get you some sympathetic help from Zektor.

Hi Beojeff,

I did speak to Jeoff Haynes on the phone and the first question he asked is if I bought the product from ebay (which I did as the HDS4 model is the only model not requiring programming but unfortunately it is discontinued).  After that, he said they would only provide email support but I never got a reply.  

turbotol

So after a couple more emails to Zector (I never got a reply, even after asking to purchase a later model Zektor switch), I dropped by the local B&O dealer who suggested installing an Atlona switch instead.  The atlona switch is a fraction of the price of the Zektor switch, comes with a remote and allows manual switching of inputs for debugging.  So for anybody facing the same problem of adding a switch to their beosystem, have a look at Atlona switches.