This thread is meant to be the continuation of this thread from the old forum, to provide updates and support about this mod. As such, this post will mostly duplicate the first post of the original thread.
For the last few years I've been the owner of (amongst other) a Beolink 5000 with a detached screen. Being an electronic engineer, I've spent some time looking for a viable (and cheap enough) way to repair the severed display ribbon cable, and found none.
So a few months ago I've spent a fair amount (okay, the vast majority to be honest) of my spare time working on a screen replacement for my Beolink 5000. I was looking for an off the shelf LCD or OLED display panel with roughly the same mechanical dimensions as the original panel, hopefully transparent as well, but again I found nothing, except an E-Ink Display with possibly matching dimensions.
For those who are not familiar with this technology, E-Ink displays are used on E-Reader tablets, have very high contrast without any sort of backlight, only requires electrical power to refresh the display (can keep a picture displayed without using any power), but quite slow refresh rate (it takes a few seconds to display a picture on the screen).
So now having a potential way forward, I started designing a PCB that would fit in the (tight) space available in the Beolink 5000. This PCB would replace the original display controller and interpret the display commands sent by the CPU as if it was the original controller, including displaying "backside-readable" text on the front side. This was actually a bit harder than I originally thought, because a few hacks were used by B&O engineers to optimise the display's function. For example "frontside-readable" text is indeed transmitted as text to the display controller, but some "backside-readable" characters are written pixels by pixel, so character recognition is required.
The end result pleases me a lot, and restores all the neat 2-way features of this remote, despite the refresh rate being a bit on the slow side
Features :
- Single sided E-Ink display ( that was a given )
- Can display all the original text and indicators (Thanks to Guy for describing to me the behavior of the some indicators on the original display)
- Nice upscaled text display (each character is now using à 29*14 font instead of 7*5 on the original display)
- Standby screen
- Low power : power consumption, and therefore battery life should be similar to the original display.
- Low battery indicator ( that one is new ! )
Here is the remote displaying the standby screen :
Login to view image
The PCB installed on top of the BL5000 upper PCB, in place of the original LCD controller IC :
Login to view image
The backside is no longer translucent, and is made of a 3D printed part that holds the display in place :
Login to view image
You can see the new display working on link.
I produced a batch of 20 kits, a few of them are still available, at the price of 60€ shipping excluded. ( I can also perform the installation on your remote, please contact me in PM ).
A kit includes :
The E-Paper display
The custom PCB
The 3D printed "cradle" for the display
A small length of wire to connect to the VBAT signal.
The installation requires some good soldering tools ( including a hot air station and a proper soldering iron ) and skills in fine soldering. The installation guide ( see link at the end of the post ) details the installation procedure. As of now this kit was installed successfully in around 10 remotes.
Useful links :
Installation guide v1.1Original thread
ERRATUM : Bad wiring diagram in installation manual.
There was a mistake in the section 6, about the signals connections on the MHS CPU. The RST pin was incorrectly placed.
I apologize for this mistake !
If you ran a jumper wire to the wrong pin in an attempt to make the connection according to this diagram, it does not seem to cause any issue, but it is better to remove it.
The installation manual v1.1 contains the correct diagram.
Login to view image
I don't even have a Beolink 5000 yet and I'd still buy one of these kits!
Outstanding job! I followed this in the old forum and am genuinely very very impressed with what you have achieved.
tentative question, what would it take to do something like this for the Beo4 - new screens are now down to NOS (New Old Stock) and will one day run out, I think the Beo4 is a corner stone of the B&O handheld controller line up and it would be a shame to not be able to fit new screens to broken models. You could perhaps even use more of the screen real estate with the source wording, add some B&O style icons for the inputs perhaps?
Either way, thanks again for this amazing contribution to the community
In my experience Beo4 screens do fail, but replacement is actually quite straightforward because connection to the PCB is via a little rubber 'contact strip' - a replacement strip is provided with the new screen. There's no soldering or anything complicated. There's a replacement thread on the old forum but the photos have yet to re-appear: /forum/general-discussion-and-questions/new-here#post-1868352
I did read a post that B&O were going to stop making/supplying new Beo4 screens, but I didn't have any problems getting hold of some recently. (EDIT: It was David656's post just above that I'd read! ?)
Yeah, not trying to scare anyone, but it is only a matter of time before screen stock drys up. I've purchased a new screen on Ebay and fitted, it is quite simple, the BEO4 remote always annoyed me it has that nice big screen and a single line of text in the middle, it would be quite cool if you could one day do an e-ink replacement and fill out more of the screen. :-)
Hi Pilatomic, In my experience Beo4 screens do fail, but replacement is actually quite straightforward because connection to the PCB is via a little rubber ‘contact strip’ – a replacement strip is provided with the new screen.
Can you describe me how the screen fails ?
I think there is a good chance the screen are actually fine, just not making proper contact.
The contact strip" is called a zebra strip, it is commonly used for connecting LCD displays, but the drawback is you now have to keep it under mechanical pressure to ensure a proper electrical connection.
Failure to maintain the correct mechanical pressure is, as far as I know, the most common failure mode for those kind of displays.
Usually, it starts with one line of dots that disappear followed by more and more.
And/or the screen contrast fading until being not readable anymore.
And obviously, screen broken or leaking.
As you said, pressing the bottom of the screen where the zebra strip is can help sometimes but not always. I tried to carefully clean the strip and tighten it but it didn't help to bring back some screens to life, so if you have any tip it would greatly help a lot of us I think!
Location: Paris France
Please Log In to Reply
You must be logged in as a BeoWorld member to post replies to forum threads.
or
Join BeoWorld
Register to access the forums, reference material, and exclusive member benefits — including our monthly prize draw.
As a Gold member you're automatically entered into our exclusive
prize draw — your chance to win iconic Bang & Olufsen products.
A unique benefit of BeoWorld Gold membership, every draw brings a new
opportunity to win something special.
