BL50 slave drops out randomly

9 replies
Hi guys
When you google this topic you actually get a hit from one of the old archived forums, sadly it isn't reachable...
I have a set of BL50 connected to a BC Core via USB.
The two speakers are connected via DPL (CAT8, 5Meters)
It has been working fine for 4-5 months, but recently the slave speaker drops out randomly...
I can then power off, and the slave is working again...  While the slave is in this non-playing state, I am still able to change the narrow/wide mode and it reacts on the slave...

Now I have been working with my local B&o Reseller to figure out where problem is...
I have tried replacing the DPL cable with a new CAT8 cable...  the problem persists here..

We then tried removing the BC Core and connecting via Wireless PL to my Eclipse, and strangely enough we are unable to replicate the problem in this setup...
For various reasons the WPL setup will not fly in the long run, so I had to switch back to BC Connect...  and promptly I got the problem again now...

I was hoping that I wasn't the only one with this problem?
So any help would be great...

I am waiting for my B&o dealer to return to me with an action plan... and it will most likely involve replacing the slave...  and eventually the master if it doesn't solve the problem..

Not sure why, but B&o has been kinda a nightmare for me since I bought a set of BL28 some years back...  I had them setup in a wireless setup, and there were _many_ problems with them... so I ended up upgrading to BL50 and all cabled setup...  and here we are.. :-)
So the next step naturally must be the BL90?...  

/H 


   

Location: Vejle, Denmark

My B&O Icons:

Beolab-50.png Beolab-50.png
Beosound-9000.png Beosound-9000.png
Beovision-Eclipse.png Beovision-Eclipse.png
Beolab-28.png Beolab-28.png
Beoplay-M5.png Beoplay-M5.png
Beosound-Stage.png Beosound-Stage.png
Beosound-Moment.png Beosound-Moment.png
Beosound-2.png Beosound-2.png
Beosound-Essence.png Beosound-Essence.png
-------------
BL50, BC Core, Eclipse, Stage, BS2, BP5, BS9000, BLC, BS Core, BS Moment, Halo. (BL28)

So today I god an USB key from the dealer with a newer version of the firmware (I am currently on 3.1.0.1187) they didn't tell me which version they sent, (can't determine from filename), just that it was the latest etc...

So... I turned on the speakers... inserted the USB key... then nothing... the USB key is lid up, but that's it... apparently it should start blinking in the LEDs, but I only have the "speaker" LED lid up.... but they told me to give it time...


My bet is that this is the same firmware I already have installed, so the speaker rejects it... but I'm not sure.. sadly there isn't a lot of information out there about this procedure...


Location: Vejle, Denmark

My B&O Icons:

Beolab-50.png Beolab-50.png
Beosound-9000.png Beosound-9000.png
Beovision-Eclipse.png Beovision-Eclipse.png
Beolab-28.png Beolab-28.png
Beoplay-M5.png Beoplay-M5.png
Beosound-Stage.png Beosound-Stage.png
Beosound-Moment.png Beosound-Moment.png
Beosound-2.png Beosound-2.png
Beosound-Essence.png Beosound-Essence.png
-------------
BL50, BC Core, Eclipse, Stage, BS2, BP5, BS9000, BLC, BS Core, BS Moment, Halo. (BL28)

The firmware on your speaker is already the latest version, (unless the dealer has received a special version from the factory)

https://update.bang-olufsen.com/update/products/8df6c854d01d44009df41bbfde777845


That being said I guess there is no harm in trying it again. The procedure for updating is to power off the speaker first, plug in the usb then power on the speaker. Both speakers must be the same version of firmware so it would be good to do both.


BeoLab 50 software update with USB flash drive

  • Connect one USB flash drive to the primary and one to the secondary speaker and plug in the power again on both speakers. The speakers will automatically detect the USB and start updating.
  • The software update on each speaker takes up to 45 mins. You do not have to remove any signal cables
  • During the software update, the light in the acoustical lens will flash green


Remark: The BeoLab 50 consists of several software components (see list below).

During a software update, you will see the BeoLab 50 rebooting several times, and in some cases the acoustical lens will move up and down.


  • When the software update has finished, the BeoLab 50 will restart, and the light in the acoustical lens will turn solid white. If no signal is sensed, the speaker will switch off.
  • In order to verify the software version, move the USB flash drive to a computer and open the file named BL50INFO.TXT (using WordPad)

Location: Leeds, West Yorkshire

My B&O Icons:

BeoCenter-9500.png BeoCenter-9500.png
Beoremote-Beo4.png Beoremote-Beo4.png
Beovox.png Beovox.png
Beotime.png Beotime.png
Beosound.png Beosound.png
Beosound-Theatre-.png Beosound-Theatre-.png
Beosound-9000.png Beosound-9000.png
Beoremote-One.png Beoremote-One.png
Beolit.png Beolit.png
Beolab-18.png Beolab-18.png
Beogram-400x.png Beogram-400x.png
Bang & Olufsen classic service centre.
Repairs and refurbishment to both old and new.

The dealer told me it may be a unreleased firmware... and they are aware that I am on the latest firmware now.


I have tried to approach you mention above with the master and slave, but not at same time, and does it has to be at the same time? I could try with two USB keys...


But as I look at the USB key's activity light as the speaker boots up, there isn't much activity, so my guess is that the file on the USB key isn't named correctly? (and I have never seen lens flash green any time...)


I was sent the USB key from the dealer, but you never know.. they also told me to turn on the speakers, and then insert the USB key... :-)

On the USB key there is one file called "dsel3.upd" at about 47MB

(so there isn't a file as you describe it...)


I hope the dealer will figure out something tomorrow...


/H



Location: Vejle, Denmark

My B&O Icons:

Beolab-50.png Beolab-50.png
Beosound-9000.png Beosound-9000.png
Beovision-Eclipse.png Beovision-Eclipse.png
Beolab-28.png Beolab-28.png
Beoplay-M5.png Beoplay-M5.png
Beosound-Stage.png Beosound-Stage.png
Beosound-Moment.png Beosound-Moment.png
Beosound-2.png Beosound-2.png
Beosound-Essence.png Beosound-Essence.png
-------------
BL50, BC Core, Eclipse, Stage, BS2, BP5, BS9000, BLC, BS Core, BS Moment, Halo. (BL28)

The file seems to be correct for the update, make sure the USB is formatted as fat32 otherwise the speaker wont read it.

Location: Leeds, West Yorkshire

My B&O Icons:

BeoCenter-9500.png BeoCenter-9500.png
Beoremote-Beo4.png Beoremote-Beo4.png
Beovox.png Beovox.png
Beotime.png Beotime.png
Beosound.png Beosound.png
Beosound-Theatre-.png Beosound-Theatre-.png
Beosound-9000.png Beosound-9000.png
Beoremote-One.png Beoremote-One.png
Beolit.png Beolit.png
Beolab-18.png Beolab-18.png
Beogram-400x.png Beogram-400x.png
Bang & Olufsen classic service centre.
Repairs and refurbishment to both old and new.

I will give it another try tomorrow... I can see the USB us FAT16 but the partition is GUID which could be MBR if you want to be compatible with your old IBM AT PC ;-)

But are we sure that just this one file is OK? Maybe it looks for "BL50INFO.TXT" ?


I still find it strange that we need to do this via USB... it may be a special firmware, but I remember on my BL28 I has _very_ many issues, and they updated it with a special firmware from the "factory"... but of cause the BL50 is older than BL28, so might make sense...


I will report back my findings...


/H

Location: Vejle, Denmark

My B&O Icons:

Beolab-50.png Beolab-50.png
Beosound-9000.png Beosound-9000.png
Beovision-Eclipse.png Beovision-Eclipse.png
Beolab-28.png Beolab-28.png
Beoplay-M5.png Beoplay-M5.png
Beosound-Stage.png Beosound-Stage.png
Beosound-Moment.png Beosound-Moment.png
Beosound-2.png Beosound-2.png
Beosound-Essence.png Beosound-Essence.png
-------------
BL50, BC Core, Eclipse, Stage, BS2, BP5, BS9000, BLC, BS Core, BS Moment, Halo. (BL28)

from memory I think BL50INFO.TXT is written to the USB by the speaker once powered on and finished booting up.

Location: Leeds, West Yorkshire

My B&O Icons:

BeoCenter-9500.png BeoCenter-9500.png
Beoremote-Beo4.png Beoremote-Beo4.png
Beovox.png Beovox.png
Beotime.png Beotime.png
Beosound.png Beosound.png
Beosound-Theatre-.png Beosound-Theatre-.png
Beosound-9000.png Beosound-9000.png
Beoremote-One.png Beoremote-One.png
Beolit.png Beolit.png
Beolab-18.png Beolab-18.png
Beogram-400x.png Beogram-400x.png
Bang & Olufsen classic service centre.
Repairs and refurbishment to both old and new.

OK it didn't create the file.... I then found out that the USB key from the dealer was created using a GPT partition... which is normal, but I guess it makes a difference because after re-formatting the key with the good old MBR from 1990'ish it seems for work...

I managed to "update" the speakers with the green light etc... but sadly the FW they send was the same I already had installed...

I have now been instructed to create a SETUP.TXT file on the key which enables debugging, and then replicate the problem....

Hopefully this will give them some clue as to what is happening...


/H

Location: Vejle, Denmark

My B&O Icons:

Beolab-50.png Beolab-50.png
Beosound-9000.png Beosound-9000.png
Beovision-Eclipse.png Beovision-Eclipse.png
Beolab-28.png Beolab-28.png
Beoplay-M5.png Beoplay-M5.png
Beosound-Stage.png Beosound-Stage.png
Beosound-Moment.png Beosound-Moment.png
Beosound-2.png Beosound-2.png
Beosound-Essence.png Beosound-Essence.png
-------------
BL50, BC Core, Eclipse, Stage, BS2, BP5, BS9000, BLC, BS Core, BS Moment, Halo. (BL28)

Glad you got it to work, its not unusual for firmware to need an old file system.

Fat32 is a lightweight filesystem which is well suited to smaller firmware components.


Hopefully the issue will be written to the log..

Location: Leeds, West Yorkshire

My B&O Icons:

BeoCenter-9500.png BeoCenter-9500.png
Beoremote-Beo4.png Beoremote-Beo4.png
Beovox.png Beovox.png
Beotime.png Beotime.png
Beosound.png Beosound.png
Beosound-Theatre-.png Beosound-Theatre-.png
Beosound-9000.png Beosound-9000.png
Beoremote-One.png Beoremote-One.png
Beolit.png Beolit.png
Beolab-18.png Beolab-18.png
Beogram-400x.png Beogram-400x.png
Bang & Olufsen classic service centre.
Repairs and refurbishment to both old and new.
or
BeoWorld Gold Membership card
Join BeoWorld

Register to access the forums, reference material, and exclusive member benefits — including our monthly prize draw.

Become a Member

December 2026 Prize Draw

Gold Members Only

As a Gold member you're automatically entered into our exclusive prize draw — your chance to win iconic Bang & Olufsen products. A unique benefit of BeoWorld Gold membership, every draw brings a new opportunity to win something special.